How To Remove Dent From Fridge Door?

Topic: How To Remove Dent From Fridge Door?

How To Remove Dent From Fridge Door

The kitchen is the heart of the house and it is a rare heart that goes through life without picking up a few dances and dents along the way. Fortunately, the door of a refrigerated refrigerator is easier to operate than an injured heart. There are many ways to repair a tooth, and you may need to try more than one. Start with a simple treatment, and instead of spending time and money on a complex treatment, work on more complicated methods that may not work for you.

Plunger method

Clean and order your pilot or buy a new one. This method works best with a flat edge plunger. Clean the area around the dental with isopropyl alcohol to ensure a tight seal. Spray the area very gently with a plant-filled with clean water. Place the rubber rim of the rider in the area around the tooth and push hard to form a seal. Pull the rider’s handle firmly toward you, but not stiff enough to break the seal. Repeat until you hear the dent.

Canned Air Duster Method

Clean your teeth and the area around them with a clean, lint-free cloth, which hardly soaks in warm water. Dry it well. Shake a container with compressed air like those used to clean computer parts and keyboards. Hold it upside down and spray the dental and the area around it. Cold carbon dioxide warms teeth as it heats up. If not, try again. If this method doesn’t work even after two or three tries, skip to the next one.

Hot glue and dent tool method

Buy a dental extraction kit designed for cars. Thoroughly clean the dent and its area with the preparation solution included in the kit. Choose a dent removal tool that is larger than the dent itself. It resembles a very large golf shirt with a very wide and flat head. For best adhesion, raise two sizes from the tooth.

Apply hot glue to the dent puller head, making sure it is thin and evenly fill the dent with a light fill in the center. Connect the dent extractor to the refrigerator with the dent at its center.

Adjust the suction cups on the different handles so they are as close to the tooth as you can. The puller handle is a metal piece with a hole in the center, adjustable suction cups on one surface and three knobs on the other surface. Bend the knees that control and adjust the legs of the shoots to loosen them and give them the right to squeeze them in place.

Slide the hole in the middle of the extraction extractor with the dent extractor handle attached to the refrigerator door and firmly attach the suction feet to the refrigerator door on either side of the tooth. Allow the contraceptive to sit for about a minute, and then tighten the center knob by turning it clockwise until it pops over the door.

If you have not ejected the tooth, clean the area again with rubbing alcohol, cover the extraction head again with hot glue, and try again. If you set the puller horizontally the first time, test it vertically the second time. It may take more than 15 tries, but if it does not affect the tooth, it may make sense to proceed to the next method.

Dryer and / or dry ice recipe

Thoroughly clean the dent and its surrounding area with a clean, damp cloth. Allow the area to dry completely. Heat the metal with a dryer on high heat. This metal can cool teeth.

Instead of heating the dent, apply thick gloves and apply dry ice to the dent surface and around the refrigerator door. Store dry ice in a safe refrigerator. Teeth can come out when the air heats up in the area.

You can also try heating the area and then applying dry ice, or vice versa.

When nothing else works

Sometimes the dent is too stubborn to get out. Or, your refrigerator door is not made of metal, and therefore not strong and flexible enough to overcome false teeth. If so, contact the manufacturer for a replacement door.

When you arrive, remove the top hinge bolt from the door. If you have an older model, you may need to remove the freezer door first. This will probably require a hex wrench. Lift the hinged door underneath and set it aside.

Carefully place the new door on the bottom hinge. Replace the top bolts and tighten them. Replace the top freezer door if necessary. Dispose of the dented refrigerator doors in accordance with the large trash regulations in your community.